Chart Attack

Ja som topic antyder så er jeg på jagt efter en bootchip til min PS2.

Jeg aner INTET om emnet, og er derfor på helt bar bund. Jeg har dog været ved at kigge rundt omkring, og har fundet denne:

Producentens side

RIPPER 2 Gold Edition

The best gift for Christmas...

Do you really need another chips?
Do you really need chips having problems with ground bounce and horrible installation?
Do you really need chips with annoying 24 or more wires to solder?
Do you really need chips with much less features then RIPPER 2 GOLD?
Do you really need chips without LED diode and without self test for easy installation?
Do you really need to save some dollars for chips, which are far behind us?
Do you really need chips powered from destructive +5V?
Do you really need chips without HDD support?
If you buy the cheap chip you will pay twice, once for the chip and secondly for upgrading to the RIPPER 2 GOLD!

We are very proud to announce RIPPER 2 GOLD.
Features:

Motherboard V9:

NEW - HDD (Hard Disc) Support (original HDD or any computer HDD).
NEW - DVD Region FREE for all PAL consoles.
NEW - DEV.olution Mode for loading apps from memory card.
NEW - Only 18 wires to solder.
NEW - RGB FIX for all PAL consoles (DVD movie mode 3x reset).
NEW Easier Chip disable feature (press reset and keep it pressed for 3 seconds from standby).
NEW - MacroVision OFF for all PAL consoles. NEW ULTRA fast PS2 boot (keep pressed the SELECT button during reset or power on).
NEW No more to press square for DVD and circle for PSX.

CD/DVD controller requires only 3 wires to be soldered to the bottom of the motherboard.
Only “B”, “G”, “I” wires to the bottom.
Less wires to the laser controller = longer laser life!
Updateable (Re-programmable) Flash Memory Integrated Circuit on board for update via CD.
Safe 3,3V power supply.
Ground Bounce effect is almost _NOT_ existent.
It means very easy install without black screen. DVD9 compatible (Xenosaga NTSC tested).
Action Replay compatible. DivX and MP3 compatibility.
Fully compatible and tested with “110 BIOS” and “MX BIOS”.
DVDR booting is very fast and reliable with 100% success.


Motherboards V3..V8 (Ripper 2 deluxe mode)

Only 17 wires to solder.
CD/DVD controller requires only 2 wires to be soldered to the bottom of the motherboard.
Only “B” and “I” wires to the bottom.
Less wires to the laser controller = longer laser life!
Updateable (Re-programmable)
Flash Memory Integrated Circuit on board for update via CD.
Safe, 3,3V power supply.
Ground Bounce effect is almost not existent.
It means very easy install without black screen.
RGB FIX for all PAL consoles (DVD movie mode)
MacroVision OFF for all PAL consoles
Booting software from memory card in dev.olution mode
DVD Region FREE for all PAL consoles
Chip disable feature (click the reset button 3 times)
DVD9 compatible (Xenosaga NTSC tested)
Action Replay compatible
DivX and MP3 compatibility
DVDR booting is very fast and reliable with 100% success.


Ripper 2 GOLD for all Pal models (17/18 wires) V3 to V9 in ONE single piece of electronics.

-------------------------------------------------------------------

Mit spørgsmål er nu om det er en god chip og om der evt. findes en der er bedre?

På forhånd tak

Kan du ikke bare tage den du have lovet mig, som du så købte og smed væk ?

Zlinky skrev:Kan du ikke bare tage den du have lovet mig, som du så købte og smed væk ?

Nææ for den har I fået igen.... Så det er vist ikke mit problem længere.